Ductless Mini-Split Installation in Austin, TX
Ductless mini-split installation for additions, garages, and rooms without ducts.
Older bungalows in Austin and additions around Rollingwood, West Lake Hills, and Lost Creek can have rooms without a supply vent or space for new ductwork. A converted garage, back bedroom, or enclosed porch may stay warmer than the rest of your house because the existing system was never designed to reach that room.
We install ductless mini-split equipment where a separate indoor unit and outdoor condenser make more sense than opening walls for ducts. The system uses a small wall opening for the refrigerant pipes, condensate drain, and control wiring, allowing the indoor unit to cool a targeted room or zone.
This work can usually be planned rather than treated as an immediate fix, because the unit location, electrical circuit, drain path, and outdoor equipment position need to suit the building. Rushing those choices can leave a room with an awkward wall unit, a difficult drain route, or equipment that does not match the space.
Hot garage and back room
Customers often call because the garage has no vent, the back bedroom stays hot after sunset, or a new addition has no cooling at all. Others are tired of a window unit blocking the window, making noise, or failing to cool the far side of the room.
A home office above the garage may be uncomfortable while the downstairs thermostat reads normally, and a sunroom can become unusable when its glass walls hold heat. A room that is cold in winter but hot in summer can also need its own indoor unit rather than more airflow from a distant register.
Those complaints can sound alike over the phone, but they can call for different equipment capacity, wall locations, electrical work, and pipe routes. We inspect the room and the available access before determining the work involved.
Installation survey and line set
We start with an installation survey of the room, exterior wall, electrical panel, and outdoor condenser location. We measure the room, check wall framing, identify a route for the pair of refrigerant pipes called the line set, and look for a condensate drain path that will not drip onto a walkway or foundation.
A survey commonly takes about 30 to 60 minutes. We also check whether the panel has room for a dedicated breaker, whether the outdoor unit can sit on a pad or wall bracket, and whether local permit or inspection requirements apply to the electrical work.
For a typical single indoor and outdoor unit layout, we mount the equipment, drill the wall opening, route the line set, install the disconnect as needed, evacuate the refrigerant circuit to a low vacuum commonly verified near 500 microns, and test operation during the installation visit. Equipment selection, permit work, panel upgrades, multi-room systems, or a route through a finished ceiling may need to be arranged for another visit; an old window unit or damaged disconnect is removed only when that work is included in the scope.
Line-set route and panel access
The route between the indoor unit and outdoor condenser has a major effect on the work. A direct exterior-wall route with open access is different from a line set that must pass through an attic, crawlspace, masonry wall, finished ceiling, or a long side yard.
Electrical panel access also matters. A panel with space for a dedicated circuit is simpler to work with than a crowded panel, a locked utility room, or wiring that needs an upgrade before the equipment can be connected.
The number of indoor units, the outdoor mounting location, drain routing, equipment availability, and any permit or inspection sign-off can also change the scope. If a specific condenser or wall unit must be ordered, the installation is planned around that equipment rather than substituted without discussion.
Model plate and room
Before you call, check which room needs cooling and whether it is a garage, bedroom, office, addition, or sunroom. Note the room’s approximate dimensions, ceiling height, window exposure, and whether a window unit or portable unit is running there now.
If you already have equipment selected, find the model number on the rating plate, usually on the side of the outdoor condenser or beneath the front cover of the indoor unit. Photos of the exterior wall, electrical panel, and proposed outdoor location help us see access, gates, stairs, and landscaping before the survey.
Tell us whether the room shares a wall with the outdoors and whether a drain can run outside or to an approved connection. Call PT Air Conditioning Austin at (737) 204-6203 before another hot spell leaves that uncooled room difficult to use.
Next: get in touch, or back to the home page.